Mounting brackets

Twin Horn Bracket allows you to install two symmetrical Horn antennas with exactly the same alignment. The bracket also accommodates mainstream 4x4 radios, such as ePMP™ 3000 or Mimosa® A5c. High density sectors or 4x4 deployments are now ingeniously s

UbiBracket is universal positioning mount for mast or wall for all NanoStation and Loco devices. The holder can be attached to a pipe up to a diameter of 60mm.

The plastic holder/stand is designed to mount selected TP-Link EAP products (see below) on a table or wall. 3 holes are made in the base measuring 83 × 100 mm to attach the bracket to the wall. The overall dimensions of the holder are

Precision Alignment Kit to better attach the antenna. Precision two-axis alignment enhances beam directivity for maximum PtP or backhaul performance. Applies to the following models airFiber®AF-5G30-S45 PowerBeam ™

Plastový držák je určený pro uchycení vybraných TP-Link produktů (viz níže) do 19" a 10" racku . V případě uchycení do 19" racku je možnost uchycení vpravo, vlevo nebo dvou držáků vedle sebe. Vnitřní rozměry rámečku jsou 226 x 131 x 35mm. Kompatibilní ...

The elegant aluminum stand with non-slip feet is only for the Cloud Key G2 Plus from Ubiquiti, which will hold the controller in an upright position. The dimensions of the base are 134 x 72 mm.

The plastic mounting box is intended for covering the cables and attaching the wall-mounted WiFi AP EAP235 and EAP615-Wall from TP-Link to the wall using two screws. The holder is made of PETG material on a 3D printer, it is white in color

The holder is intended for attaching selected Deco wireless Access Point units of the TP-Link brand to the wall using two screws. The holder is made of PETG material on a 3D printer and is white in color. The mount is only compatible

The plastic holder is designed to hold selected MikroTik products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

Plastový držák je určený pro uchycení vybraných MikroTik produktů (viz níže) do 19" a 10" racku . V případě uchycení do 19" racku je možnost uchycení vpravo, vlevo nebo dvou držáků vedle sebe. Vnitřní rozměry rámečku jsou 119 x 33 mm. Kompatibilní se z...

The holder is designed for attaching TP-Link Deco M9 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.

Plastový držák/stojan je určený pro uchycení vybraných TP-Link EAP produktů (viz níže) na stůl či zeď . Pro uchycení držáku na zeď jsou v podstavě o rozměrech 83 x 100 mm vytvořeny 3 otvory. Celkové rozměry držáku jsou 106 x 83 x 153 mm. Kompatibilní s...

The plastic wall mount is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Lite, UAP-nanoHD and UAP-AC-Lite. The holder is attached to the wall using two screws

The plastic wall holder is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Pro and UAP-AC-PRO. The holder is attached to the wall using two screws and dowels, which are in

Plastový stojan pro TP-Link EAP610-Outdoor venkovní WiFi jednotku. Stojan umožňuje instalace na strop (rozměr podstavce je 83x100mm) nebo na stůl. Patice držáku umožňuje bezproblémové držení EAP jednotky, ať už je držák na stole či na stropě. Rozměry d...

Plastový stojan pro TP-Link EAP235-Wall a EAP615-Wall WiFi Access point jednotky. Stojan umožňuje instalace na stůl (rozměr podstavce je 81x120mm). Celkové rozměry stojanového držáku jsou 81 x 120 x 88 mm a je vyroben z šedého PETG fillamentu pomocí 3D...

Plastový držák je určený pro uchycení bezdrátových jednotek HALO H70X a HALO H80X značky MERCUSYS na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 135 x 116 x 40mm.

The plastic holder is used for the horizontal installation of UniFi Access Points from Ubiquiti U6-Lite, UAP-nanoHD and UAP-AC-Lite on the wall or as a stand on a table. The holder can be installed with the UniFi plate up and

The plastic holder is used for horizontal installation of UniFi Access Points from Ubiquiti U6-PRO and UAP-AC-PRO on the wall or as a stand on a table. The holder can be installed with the UniFi plate up and down and

Plastový držák je určený pro uchycení bezdrátových jednotek HX220 a HC220 značky TP-Link na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 110 x 140 x 40mm.

Excellent plastic holder designed for places where it is not possible to drill, so thanks to the suction cup it can be mounted from the inside of the window. The bracket is compatible with NBE-5AC-16 and NBE-M5-16.

U-PRO-MP universal mounting system is more versatile than standard plastic holders and can be mounted on wall or plastic boxes of different sizes in the wall. The system is compatible with these drives: UAP-AC-PRO UAP-AC-HD

NanoHD-RCM-3 is a three-pack of ceiling mounts for UAP nanoHD, U6-Lite, U6-Lite or U6+, thanks to which you can embed your devices in the ceiling. Both packaging (3) ceiling mount

NanoHD-RetroFit-3 is a mounting kit for attaching the UAP-nanoHD unit to the wall or ceiling with the original UAP, UAP-LR mounts. Once mounted, your UAP-nanoHD, U6 Lite or U6+ will blend in with the walls because the Retrofit Mount kit elimina

Excellent plastic holder designed to places where it is not possible to drill through the suction cup so it can be mounted on the window. The holder can be locked in all directions.

The Universal Arm Bracket is designed for convenient wall or pole mounting of the NanoStation®M. 90° tilt adjustment allows for easy positioning.

EasyBracketTM for ePMPTM allows the installation of ePMP1000TM Radios to Ubiquiti AirMAX Sectors, RF elements Sectors and other antennas with compatible radio quick-mounting system. EasyBracket for ePMP is made of high quality Polycarbonate. Installati

NBE-WMK Wall Mount Kit is for enhanced stability when mounting the NanoBeam on a wall.

Toolless Quick-Mounts for Ubiquiti CPE Products. Designed for additional mounting flexibility and device alignment options, the Quick-Mount accessory kit features an easy-to-use, toolless design. Features No tools r

The 60 GHz Precision Alignment Mount enhances mounting flexibility and device alignment. It features an easy-to-use design that requires only an Allen wrench (included) to align.